Published journal papers

Lazar Milić, Dejan Movrin, Mitar Simić, Varun Jeoti, Goran Stojanović, “Investigation of electrical performances of textile conductive lines under different connector configurations and external influences”, Textile Research Journal (IF: 2.455), 2022, DOI: 10.1177/00405175221145553.

Ankita Sinha, Adrian K. Stavrakis, Mitar Simić, Goran M. Stojanović, “Wearable humidity sensor embroidered on a commercial face mask and its electrical properties”, Journal of Materials Science (IF:  4.682), 58, pp. 1680-1693, 2023, https://doi.org/10.1007/s10853-022-08135-2

Mitar Simić, Adrian K. Stavrakis, Tijana Kojić, Varun Jeoti, Goran M. Stojanović, “Parameter Estimation of the Randles Equivalent Electrical Circuit Using Only Real Part of the Impedance”, IEEE Sensors Journal (IF: 4.325), doi: 10.1109/JSEN.2023.3238074, 2023.

Mitar Simić, Adrian K. Stavrakis, Milan Radovanović, Asif Iqbal, Varun Jeoti, Goran M. Stojanović, “A Portable Device for Passive LC Sensors Readout with Low-Coupling Enhanced Sensitivity”, IEEE Transactions on Instrumentation & Measurement (IF: 5.332), vol. 72, pp. 1-12, 2023, doi: 10.1109/TIM.2022.3232089

Ankita Sinha, Adrian K. Stavrakis, Mitar Simić, Sanja Kojić, Goran M. Stojanović, “Gold Leaf-Based Microfluidic Platform for Detection of Essential Oils Using Impedance Spectroscopy”, Biosensors (IF: 5.743), 2022, 12, 1169. https://doi.org/10.3390/bios12121169

Mitar Simić, Adrian K. Stavrakis, Goran M. Stojanović, “Portable Heating and Temperature-Monitoring System with a Textile Heater Embroidered on the Facemask”, ACS Omega (IF: 4.132), 2022, https://doi.org/10.1021/acsomega.2c06431

Ankita Sinha, Adrian K. Stavrakis, Mitar Simic, Goran M. Stojanovic, “Polymer-Thread-Based Fully Textile Capacitive Sensor Embroidered on a Protective Face Mask for Humidity Detection”, ACS Omega (IF: 4.132),  2022, 7, 44928−44938,  https://doi.org/10.1021/acsomega.2c05162

Zoran Bobić, Sanja Kojić, Goran M. Stojanović, Vladimir Terek, Lazar Kovačević, Pal Terek, “Nanotopography Evaluation of NiTi Alloy Exposed to Artificial Saliva and Different Mouthwashes”, Materials (IF: 3.748), 2022, 15, 8705, https://doi.org/10.3390/ma15238705 

Bozica Kovacevic, Susbin Raj Wagle, Corina Mihaela Ionescu, Melissa Jones, Michael Lewkowicz, Elaine YM Wong, Sanja Kojic, Goran Stojanovic, Maja Đanić, Momir Mikov, Armin Mooranian, Hani Al-Salami, “Novel hydrogel comprising non-ionic copolymer with various concentrations of pharmacologically active bile acids for cellular injectable gel”, Colloids and Surfaces B: Biointerfaces (IF: 5.999), 11 November 2022, 113014, doi: 10.1016/j.colsurfb.2022.113014

Nuraina Anisa Dahlan, Aung Thiha, Fatimah Ibrahim, Lazar Milić, Shalini Muniandy, Nurul Fauzani Jamaluddin, Bojan Petrović, Sanja Kojić, Goran M. Stojanović, “Role of Nanomaterials in the Fabrication of bioNEMS/MEMS for Biomedical Applications and towards Pioneering Food Waste Utilisation”, Nanomaterials (IF: 5.719), 2022, 12, 4025, https://doi.org/10.3390/nano12224025

Selvakumar Guruswamy, Milica Pojić, Jayashree Subramanian, Jasna Mastilović, Sohail Sarang, Arumugam Subbanagounder, Goran Stojanović, Varun Jeoti, “Toward Better Food Security Using Concepts from Industry 5.0”, Sensors (IF: 3.847) 2022, 22, 8377, https://doi.org/10.3390/s22218377

Adrian K. Stavrakis, Mitar Simić, Goran M. Stojanović, “A Study of the Performance Degradation of Conductive Threads Based on the Effects of Tensile Forces and Repeated Washing”, Polymers (IF: 4.967) 2022, 14, 4581, https://doi.org/10.3390/polym14214581

Adnan E. Ali, Goran M. Stojanović, Varun Jeoti, Dalibor Sekulić, Ankita Sinha, “Impact of Various Wearability Conditions on the Performances of Meander-Line Z-Shaped Embroidered Antenna”, International Journal of Antennas and Propagation (IF: 1.244), vol. 2022, Article ID 6741689, 15 pages, https://doi.org/10.1155/2022/6741689

Sanja Kojić, Mitar Simić, Milica Aber, Bojan Petrović, Goran M Stojanović, “Influence of artificial saliva and essential oil-based solutions on the electrical parameters of Nitinol and stainless steel archwires”, Materials and Technology (IF: 0.650), 2022, 56 (5), 445–452, doi: 10.17222/mit.2022.415

Muhammad Umar Aslam Khan, Saiful Izwan Abd Razak, Sarish Rehman, Anwarul Hasan, Saima Qureshi, Goran M. Stojanović, ”Bioactive scaffolds from (Sodium Alginate-co-Acrylic Acid)-g-(nHAp@SiO2@GO) for bone tissue engineering”, International Journal of Biological Macromolecules (IF: 8.025), 222 (2022) 462–472, https://doi.org/10.1016/j.ijbiomac.2022.09.153

Bojan Petrović, Nebojsa Stilinović, Ana Tomas, Sanja Kojić, Goran M.  Stojanović, “Determination of salivary concentrations of leptin and adiponectin, ability to reduce ferric ions and total antioxidant capacity of saliva in patients with severe early childhood caries”, Frontiers in Pediatrics (IF: 3.569) 10:969372, 2022, doi: 10.3389/fped.2022.969372

Ankita Sinha, Adrian K. Stavrakis, Saima Qureshi, Goran M. Stojanović, “Flexible polyamide-based dental floss sensor for pH monitoring”, Materials Letters (IF: 3.574), 326 (2022) 132971, doi: https://doi.org/10.1016/j.matlet.2022.132971

Tijana Kojić, Mitar Simić, Milica Pojić, Goran M. Stojanović, “Detecting freshness of fruit and vegetable without and with edible protein-based foil”, IEEE Sensors Journal (IF: 4.325), vol. 22, no. 16, pp. 15698-15705, 2022, doi: 10.1109/JSEN.2022.3188388

Saima Qureshi Lazar Milić, Bojan Petrović, Marija Vejin, Sanja Kojić, Stefan Jarić, Goran Stojanović, “The Measurement of Contact Angle, pH, and Conductivity of Artificial Saliva and Mouthwashes on Enamel, Glass-Ionomer, and Composite Dental Materials”, Materials (IF: 3.748) 2022, 15, 4533, pp. 1-15, https://doi.org/10.3390/ma15134533

Mitar Simić, Adrian K. Stavrakis, Varun Jeoti, Goran M. Stojanović, “A Randles Circuit Parameter Estimation of Li-ion Batteries with Embedded Hardware”, IEEE Transactions on Instrumentation and Measurement (IF: 5.332), vol. 71, pp. 1-12, 2022, doi: 10.1109/TIM.2022.3183661

Ines Nikolić, Mitar Simić, Ivana Pantelić, Goran Stojanović, Jelena Antić Stanković, Bojan Marković,Snežana Savić, “Chemical vs. Physical Methods to Improve Dermal Drug Delivery: A Case Study with Nanoemulsions and Iontophoresis”, Pharmaceutics (IF: 6.525), 2022, 14, 1144,  https://doi.org/10.3390/pharmaceutics14061144

Mitar Simić, Adrian K. Stavrakis, Ankita Sinha, Velibor Premčevski, Branko Markoski, Goran M. Stojanović, “Portable Respiration Monitoring System with an Embroidered Capacitive Facemask Sensor”, Biosensors (IF: 5.743) 2022, 12, 339,  https://doi.org/10.3390/bios12050339

Muhammad Umar Aslam Khan, Saiful Izwan Abd Razak, Anwarul Hassan, Saima Qureshi, Goran M. Stojanović, Ihsan-ul-Haq, “Multifunctional ARX-f-GO based composite hydrogels for wound healing application”, Frontiers in Bioengineering and Biotechnology (IF: 6.064), volume 10, Article 8650592, pp. 1-12, 2022, doi: 10.3389/fbioe.2022.865059

Ankita Sinha, Dhanjai, Adrian K. Stavrakis, Goran M. Stojanović, “Textile-based electrochemical sensors and their application”, Talanta (IF: 6.556), 123425 (2022), https://doi.org/10.1016/j.talanta.2022.123425

Tijana Kojic, Bozica Kovacevic, Ankita Sinha, Mitar Simić, Goran M. Stojanović, “Silver Thread‐Based Microfluidic Platform for Detection of Essential Oils Using Impedance Spectroscopy”, Applied Sciences (IF: 2.838), 2022, 12, 3596, https://doi.org/10.3390/app12073596

Aan Nazmus Sakib, Micheal Drieberg, Sohail Sarang, Azrina Abd Aziz, Nguyen Thi Thu Hang, Goran M. Stojanović, “Energy-Aware QoS MAC Protocol Based on Prioritized-Data and Multi-Hop Routing for Wireless Sensor Networks”, Sensors (IF: 3.847), 2022, 22, 2598, https://doi.org/10.3390/s22072598

A. Iqbal, M. Drieberg, V. Jeoti, A. B. Abd Aziz, G. Stojanović, M. Simić, and N. Hussain „A Flexible Multiband Multicarrier Signal Design for Broadband Channel Sounding Applications“, Human-centric Computing and Information Sciences (IF: 6.558),  vol. 12, no. 19, pp. 1-17, 2022. (https://doi.org/10.22967/HCIS.2022.12.019)

Adrian K. Stavrakis, Sanja Kojić, Bojan Petrović, Isidora Nešković, Goran M. Stojanović, “Performance evaluation of dental flosses pre- and post- utilization”, Materials (IF: 3.847) 2022, 15, 1522, https://doi.org/10.3390/ma15041522

Hima Zafar, Asma Channa, Varun Jeoti, Goran M. Stojanović, “Comprehensive Review on Wearable Sweat-Glucose Sensors for Continuous Glucose Monitoring”, Sensors (IF: 3.576), 2022, 22, 638. https://doi.org/10.3390/s22020638

Armin Mooranian, Corina Mihaela Ionescu, Susbin Raj Wagle, Bozica Kovacevic, Daniel Walker, Melissa Jones, Jacqueline Chester, Thomas Foster, Edan Johnston, Sanja Kojic, Goran M. Stojanović, Momir Mikov, Hani Al-Salami, “Taurine grafted islets improved drug-pharmacology without direct dependency between interleukin-6 and lithocholic acid in plasma”, Biomedicines (IF: 4.757), 2022, 10(1), 111; https://doi.org/10.3390/biomedicines10010111

Saima Qureshi, Goran M. Stojanović, Mitar Simić, Varun Jeoti, Najeebullah Lashari, Farooq Sher, “Silver Conductive Threads-Based Embroidered Electrodes on Textiles as Moisture Sensors for Fluid Detection in Biomedical Applications”, Materials (IF: 3.748), 14, no. 24: 7813, 2021, https://doi.org/10.3390/ma14247813

M. Hanif, V. Jeoti, M. Radzi Ahmad, M. Zubair Aslam, S. Qureshi, G. Stojanovic, “FEM analysis of various multilayer structures for CMOS compatible wearable acousto-optic devices”, Sensors (IF: 3.847), 2021, 21, 7863, https://doi.org/10.3390/ s21237863

G. M. Stojanović, A. Sinha, A. E. Ali, V. Jeoti, M. B. Radoičić, D. D. Marković, M. M. Radetić, “Impedance analysis of milk quality using functionalized polyamide textile-based sensor”, Computers and Electronics in Agriculture (IF: 6.757), 191 (2021) 106545, https://doi.org/10.1016/j.compag.2021.106545

A. Mooranian, C. Mihaela Ionescu, S. Raj Wagle, B. Kovačević, D. Walker, M. Jones, J. Chester, T. Foster, E. Johnston, S. Kojić, G. Stojanović, M. Mikov, H. Al-Salami, “Polyelectrolytes Formulated with Primary Unconjugated Bile Acid Optimised Pharmacology of Bio-engineered Implant”, Pharmaceutics (IF: 6.525), 2021, 13, 1713. https://doi.org/ 10.3390/pharmaceutics13101713.

Mitar Simić, Adrian K. Stavrakis, Goran M. Stojanović, “A Low-Complexity Method for Parameter Estimation of the Simplified Randles Circuit With Experimental Verification”, IEEE Sensors Journal (IF: 4.325), 2021, doi: 10.1109/JSEN.2021.3110296

Adnan E. Ali, Varun Jeoti, and Goran M. Stojanović, “Fabric based printed – distributed battery for electronic textiles and wearables: A review”, Science and Technology of Advanced Materials (IF: 7.821), 2021, vol. 22, no. 1, pp. 772-793, doi: https://doi.org/10.1080/14686996.2021.1962203

S. Kasyap, V. Jeoti, M. Drieberg, S. Soeung, A. Iqbal, G. Stojanović, S. Sarang, “Simultaneous Detection of Multiple Surface Acoustic Wave Sensor-Tags for Water Quality Monitoring utilizing Cellular Code-Reuse Approach”, IEEE Internet of Things Journal (IF: 10.238), doi: 10.1109/JIOT.2021.3082141, 2021

R. Prodanović, S. Sarang, D. Rančić, I. Vulić, G. M. Stojanović, S. Stankovski, G. Ostojić, I. Baranovski, D. Maksimović, “Trustful Wireless Sensor Network for Monitoring Humidity and Moisture Environments”, Sensors (IF: 3.275), 2021, 21(11), 3636; https://doi.org/10.3390/s21113636

Goran M. Stojanović, Tijana Kojić, Mitar Simić, Milan Radovanović, Sanja Panić, Vladimir V. Srdić, Saša Vukmirović, Gaewyn Ellison, Hani Al-Salami, “A functionalized paper strip-based platform for rapid detection of anticancer drug concentrations”, Journal of Sensors (IF: 2.336), 2021, Article ID 5558859, https://doi.org/10.1155/2021/5558859

G. M. Stojanović, T. Kojić, M. Simić, A. Jovanović-Galović, B. Pavlović, A. Zurutuza, L. Anzi, R. Sordan, “Rapid Selective Detection of Ascorbic Acid Using Graphene-Based Microfluidic Platform“, IEEE Sensors Journal (IF: 4.325), vol. 21, no. 15, pp. 16744 – 16753, 2021, DOI: 10.1109/JSEN.2021.3078692

A.K. Stavrakis, M. Simić, G. Stojanović, “Electrical Characterization of Conductive Threads for Textile Electronics“, Electronics (IF: 2.690) 2021, 10, 967. https://doi.org/10.3390/electronics10080967.

I. Podunavac, S. Hinić, S. Kojić, N. Jelenčiakova, V. Radonić, B. Petrović, G. Stojanović, “Microfluidic Approach for Measurements of pH, O2, and CO2 in Saliva”, Sensors and Materials (IF: 0.879), vol. 33, no. 3 (2021) 1037-1050. https://doi.org/10.18494/SAM.2021.3219

I. Podunavac, S. Hinić, S. Kojić, N. Jelenčiakova, V. Radonić, B. Petrović, G. Stojanović, “Microfluidic Platform for Examination of Effect of Chewing Xylitol Gum on Salivary pH, O2, and CO2”, Applied Sciences (IF: 2.838), 2021, 11, 2049. https://doi.org/10.3390/app11052049

M. Radovanović, M. Ilić, K. Pastor, M. Ačanski, S. Panić, V. V. Srdić, D. Randjelović, T. Kojić, G. Stojanović, “Rapid detection of olive oil blends using a paper-based portable microfluidic platform”, Food Control (IF: 6.652), 107888, 2021, https://doi.org/10.1016/j.foodcont.2021.107888

A. Chandran M. K., B. Bajac, G. Filipič, Ž. Cvejić, V. V. Srdić, M. Radovanović, M. Simić, S. Sarang, G. Stojanović, “Synthesis and Characterization of Tin Oxide Nanopowder and Its Application to Sensing Different Pathogens”, Sensors and Materials (IF: 0.879), vol. 33, no. 2 (2021) 513-527, https://doi.org/10.18494/SAM.2021.3090

S. Hinić, B. Petrović, S. Kojić, N. Omerović, J. Jevremov, N. Jelenciakova, G. Stojanović, “Viscosity and mixing properties of artificial saliva and four different mouthwashes”, Biorheology (IF: 1.615), vol. 57, no. 2-4, pp. 87-100, 2020, doi: 10.3233/BIR-201008

A. Chandran, J. Zavašnik, Z. Cvejić, S. Sarang, M. Simić, V. Srdić, G. Stojanović, “Performances and biosensing mechanisms of interdigitated capacitive sensors based on the hetero-mixture of SnO2 and In2O3”, Sensors (IF: 3.275), 2020, 20, 6323; doi:10.3390/s20216323

S. Sarang, G. Stojanović, S. Stankovski, Ž. Trpovski, M. Drieberg, “Energy-Efficient Asynchronous QoS MAC Protocol for Wireless Sensor Networks”, Wireless Communications and Mobile Computing (IF: 1.819), Volume 2020, Article ID 8860371, 13 pages, https://doi.org/10.1155/2020/8860371

S. R. Wagle, B. Kovacevic, D. Walker, C. Mihaela Ionescu, M. Jones, G. Stojanovic, S. Kojic, A. Mooranian, H. Al-Salami, “Pharmacological and Advanced Cell Respiration Effects, Enhanced by Toxic Human-Bile Nano-Pharmaceuticals of Probucol Cell-Targeting Formulations”, Pharmaceutics (IF: 4.421), 2020, 12, 708; doi:10.3390/pharmaceutics12080708

S. Kojić, S. Birgermajer, V. Radonić, I. Podunavac, J. Jevremov, B. Petrović, E. Marković, G. Stojanović, “Optimization of hybrid microfluidic chip fabrication methods for biomedical application”, Microfluidics and Nanofluidics (IF: 2.489), 2020, 24:66, pp. 1-12,  https://doi.org/10.1007/s10404-020-02372-0

S R Wagle, B. Kovacevic, D. Walker, C. M. Ionescu, U. Shah, G. Stojanovic, S. Kojic, A. Mooranian, H. Al-Salami, “Alginate-based drug oral targeting using bio-micro/nano encapsulation technologies”, Expert Opinion on Drug Delivery (IF: 4.838), 2020 Oct; 17(10): 1361-1376. https://doi.org/10.1080/17425247.2020.1789587

G. Stojanović, M. Radetić, Z. Šaponjić, M. Radoičić, M. Radovanović, Ž. Popović, S. Vukmirović, “Textile-based microfluidic platform for detection of cytostatic drug concentration from sweat samples”, Applied Sciences (IF: 2.474), 10, 4392; 2020, ISSN: 2076-3417, doi:10.3390/app10124392

M. Simić, T. Kojić, M. Radovanović, G. Stojanović, H. Al-Salami, “Impedance Spectroscopic Analysis of the Interdigitated Flexible Sensor for Bacteria Detection”, IEEE Sensors Journal (IF: 3.073), vol. 20, no. 21, pp. 12791-12798, 2020, doi: 10.1109/JSEN.2020.3002839, ISSN: 1530-437X

G. Stojanović, J. Nikodinović-Runić, S. Švenderman, T. Kojić, M. Radovanović, M. Mikov, D. Ranđelović, “Comprehensive characterization of elastomeric polyhydroxyalkanoate and its sensor applications”, Materials Science and Engineering: C (IF: 5.880), vol. 115, October 2020, 111091, https://doi.org/10.1016/j.msec.2020.111091

T. Kojić, M. Radovanović, G. Stojanović, B. Pivaš, D. Medić, H. Al-Salami, “Comparison of performances of flexible sensors on foil and paper for efficient bacterial concentration measurement”, Sensor Review (IF: 1.217), vol. 40, no. 1, pp. 1-7, 2020, https://doi.org/10.1108/SR-04-2018-0082

A. Mooranian, S. R. Wagle, B. Kovacevic, R. Takechi, J. Mamo, V. Lam, G. F. Watts, M. Mikov, S. Golocorbin-Kon, G. Stojanovic, H. Al-Sallami, H. Al-Salami, “Bile acid bio-nanoencapsulation improved drug targeted-delivery and pharmacological effects via cellular flux: 6-months diabetes preclinical study”, Scientific Reports (IF: 3.998), (2020) 10(1):106, https://doi.org/10.1038/s41598-019-53999-1

A. Mooranian, N. Zamani, M. Mikov, S. Goločorbin-Kon, G. Stojanović, F. Arfuso, B. Kovacevic, H. Al-Salami, “A second-generation micro/nano capsules of an endogenous primary un-metabolised bile acid, stabilized by Eudragit-alginate complex with antioxidant compounds”, Saudi Pharmaceutical Journal (IF: 2.879), vol. 28, no. 2, pp. 165-171, 2020, https://doi.org/10.1016/j.jsps.2019.11.017

M. Samae, P. Ritmetee, S. Chirasatitsin, S. Kojić, T. Kojić, J. Jevremov, G. Stojanović, H. Al Salami, “Precise manufacturing and performance validation of paper-based passive microfluidic micromixers”, International Journal of Precision Engineering and Manufacturing (IF: 1.378), vol. 21, no. 3, pp. 499-508, 2020, DOI: 10.1007/s12541-019-00272-0

M. Simić, Z. Babić, V. Risojević, G. Stojanović, “Non-iterative parameter estimation of the 2R-1C model suitable for low-cost embedded hardware“, Frontiers of Information Technology & Electronic Engineering (IF: 1.604), 21(3), pp. 476-490, 2020, https://doi.org/10.1631/FITEE.1900112

M. Radovanović, D. Vasiljević, D. Krstić, I. Antić, O. Korzhyk, G. Stojanović, B. Škrbić, “Flexible sensors platform for determination of cadmium concentration in soil samples, Computers and Electronics in Agriculture (IF: 3.858), 166 (2019) 105001, https://doi.org/10.1016/j.compag.2019.105001

G. Stojanović, M. Paroški, N. Samardžić, M. Radovanović, D. Krstić, “Microfluidics-based four fundamental electronic circuit elements resistor, inductor, capacitor and memristor”, Electronics (IF: 2.412), vol. 8, no. 9, pp. 960-972, 2019. https://doi.org/10.3390/electronics8090960, ISSN: 2079-9292

G. Stojanović, M. Radovanović, D. Krstić, I. Ignjatović, J. Dragaš, V. Carević, “Determination of pH in powdered concrete samples or in suspension”, Applied Sciences (IF: 2.474), 2019, 9(16), 3257, doi:10.3390/app9163257

G. Stojanović, M. Pojić, S. Kojić, A. Mišan, D. Vasiljević, “Mechanical properties of edible biofilm as a substrate for printed electronics”, Applied Physics A: Materials Science & Processing (IF: 1.810), vol. 125, pp. 576-583, 2019, DOI: 10.1007/s00339-019-2881-5, ISSN: 0947-8396

A. Mooranian, N. Zamani, G. Luna, H. Al-Sallami, M. Mikov, S. Goločorbin-Kon, G. Stojanović, F. Arfuso, B. Kovacevic, H. Al-Salami, “Bile acid-polymer-probucol microparticles: protective effect on pancreatic β-cells and decrease in Type 1 diabetes development in a murine mode”, Pharmaceutical Development and Technology (IF: 2.169), vol. 24, no. 10, pp. 1272-1277, 2019, https://doi.org/10.1080/10837450.2019.1665069

N. Jovanović, B. Petrović, S. Kojić, M. Šipovac, D. Marković, S. Stefanović, G. Stojanović, “Primary Teeth Bite Marks Analysis on Various Materials: A Possible Tool in Children Health Risk Analysis and Safety Assessment”, Int. J. Environ. Res. Public Health (IF: 2.849) 2019, 16, 2434; doi:10.3390/ijerph16132434

G. Stojanović, M. Radovanović, D. Vasiljević, T. Kojić, B. Pivaš, T. Puškar, S. Kapadia, R. Baumann, “Comparison of performances of flexible tailor-made force sensing resistors fabricated using ink-jet and xurographic techniques”, Journal of Sensors (IF: 1.595), Volume 2019, Article ID 9181492, 8 pages, https://doi.org/10.1155/2019/9181492

G. Stojanović, T. Kojić, M. Radovanović, D. Vasiljević, S. Panić, V. Srdić, J. Cvejić, “Flexible sensors based on two conductive electrodes and MWCNTs coating for efficient pH value measurement”, Journal of Alloys and Compounds (IF: 4.650), vol. 794, pp. 76-83, 2019, https://doi.org/10.1016/j.jallcom.2019.04.243, ISSN: 0925-8388

B. Petrović, S. Kojić, T. Perić, M. Šipovac, J. Lazarević, S. Stefanović, G. Stojanović, “Surface characterisation of the raw and cooked bovine cortical metatarsal bone”, Acta of Bioengineering and Biomechanics (IF: 0.968), vol. 21, no. 1, 2019, ISSN 1509-409X, DOI: 10.5277/ABB-01197-2018-02

B. Petrović, D. Marković, S. Kojić, T. Perić, G. Dubourg, M. Drljača, G. Stojanović, “Characterization of glass ionomer cements stored in various solutions”, Materials and technology (IF: 0.697) 53 (2019) 2, pp. 285-293, ISSN 1580-2949, doi: 10.17222/mit.2018.159

S. Kojić, G. Stojanović, V. Radonić, “Novel cost-effective microfluidic chip based on hybrid fabrication and its comprehensive characterization”, Sensors (IF: 3.275), 2019, 19(7), 1719; https://doi.org/10.3390/s19071719, ISSN: 1424-8220

M. Marković, J. Bajić, M. Batilović, Z. Sušić, A. Joža, G. Stojanović, “Comparative Analysis of Deformation Determination by Applying Fiber-optic 2D Deflection Sensors and Geodetic Measurements”, Sensors (IF: 3.275), vol. 19, no. 4, pp. 844-858, 2019. ISSN: 1424-8220, doi:10.3390/s19040844

I. Vranić, I. Vranić, B. Antić, G. Stojanović, H. Al-Salami, “Influence of the Main Filter on QRS-amplitude and Duration in Human Electrocardiogram”, Measurement Science Review (IF: 0.900), vol. 19, no. 1, pp. 29-34, 2019, ISSN: 1335-8871, https://doi.org/10.2478/msr-2019-0005

T. Kojić, G. Stojanović, A. Miletić, M. Radovanović, H. Al-Salami, F. Arduini, “Testing and Characterization of Different Papers as Substrate Material for Printed Electronics and Application in Humidity Sensor”, Sensors and Materials (IF: 0.599), vol. 31, no. 9, pp. 2981-2995, 2019. https://doi.org/10.18494/SAM.2019.2473, ISSN: 0914-4935

A. Mooranian, N. Zamani, M. Mikov, S. Goločorbin-Kon, G. Stojanovic, F. Arfuso, H. Al-Salami, “Novel nano-encapsulation of probucol in microgels: scanning electron micrograph characterizations, buoyancy profiling, and antioxidant assay analyses”, Artificial Cells, Nanomedicine, and Biotechnology (IF: 4.462), 46(sup3): S741-S747, 2018, DOI: 10.1080/21691401.2018.1511571, ISSN: 2169-1401

S. Thamphiwatana, T. Phairatana, S. Chirasatitsin, M. Samae, G. V. Casquillas, H. Al-Salami, S. Kojić, G. Stojanović, “A microfluidic micromixer fabricated using polydimethylsiloxane-based platform for biomedical applications”, Informacije MIDEM – Journal of Microelectronics, electronic components and materials (IF: 0.356), vol. 48, no. 3, pp. 181-187, 2018, ISSN: 0352-9045

D. Vasiljević, A. Mansouri, L. Anzi, R. Sordan, G. Stojanović, “Performance Analysis of Flexible Ink-jet Printed Humidity Sensors Based on Graphene Oxide”, IEEE Sensors Journal (IF: 3.076), vol. 18, no. 11, pp. 4378-4383, 2018, ISSN 1530-437X, doi: 10.1109/JSEN.2018.2823696

M. Radovanović, S. Kojić, D. Vasiljević, G. Stojanović, “Characterization of LC sensor structures realized by PCB and LTCC technology for determining moisture in building materials”, Processing and Application of Ceramics (IF: 0.976), vol. 12, no. 1, pp. 13-20, 2018, ISSN: 1820-613, https://doi.org/10.2298/PAC1801013R

N. Samardžić, B Bajac, J. Bajić, E. Đurđić, B. Miljević, V. V. Srdić, G. M. Stojanović, “Photoresistive switching of multiferroic thin film memristors”, Microelectronic Engineering (IF: 1.654), vol. 187-188, pp. 139-143, 2018, ISSN: 0167-9317, https://doi.org/10.1016/j.mee.2017.10.018

G. Stojanović, N. Lečić, S. Kojić, D. Vasiljević, “Characterization of customized ferrite cores for a compact six-phase coupled inductor”, International Journal of Applied Electromagnetics and Mechanics (IF: 0.684), vol. 57, pp. 19-27, 2018, ISSN: 1383-5416, DOI: 10.3233/JAE-170031

A. Pajkanović, M. Videnović-Misić, G. Stojanović, “Design and Characterization of a 130 nm CMOS Ultra-Wideband Low-Noise Amplifier”, Informacije MIDEM – Journal of Microelectronics, electronic components and materials (0.476), vol. 47, no. 2, pp. 59-70, 2017, ISSN: 0352-9045

N. Samardžić, B. Bajac, V, Srdić, G. Stojanović, “Conduction Mechanisms in Multiferroic Multilayer BaTiO3/NiFe2O4/BaTiO3 Memristors”, Journal of Electronic Materials (IF: 1.566), vol. 46, no. 10, pp. 5492-5496, 2017, ISSN: 0361-5235, DOI: 10.1007/s11664-017-5618-2.

D. Vasiljević, D. Brajković, D. Krklješ, B. Obrenović, G. Stojanović, “Testing and characterization of multilayer force sensing resistors fabricated on flexible substrate”, Informacije MIDEM – Journal of Microelectronics, electronic components and materials (0.476), vol. 47, no. 1, pp. 40-48, 2017, ISSN: 0352-9045.

K. Babković, M. Damnjanović, L. Nagy, M. Kisić, G. Stojanović, “Inductive Displacement Sensor of Novel Design Printed on Polyimide Foil”, IEEE Transactions on Magnetics (IF: 1.467), vol. 53, no. 4, 7776944, 2017, ISSN: 0018-9464, DOI: 10.1109/TMAG.2016.2636820

M. Simić, L. Manjakkal, K. Zaraska, G. M. Stojanović, D. Ravinder, “TiO2-Based Thick Film pH Sensor”, IEEE Sensors Journal (IF:2.617) , vol. 17, no. 2 pp. 248-255, 2017, ISSN: 1530-437X, doi: 10.1109/JSEN.2016.2628765

D. Krklješ, G. Stojanović, “An Ink-Jet Printed Capacitive Sensor for Angular Position/Velocity Measurements”, Advances in Electrical and Computer Engineering (IF: 0.459), vol. 16, no. 4, pp.  77-82, 2016, ISSN: 1582-7445, doi: 10.4316/AECE.2016.04012

M. Simić, Z. Babić, V. Risojević, G. Stojanović, “Novel Non-Iterative Method for Real-Time Parameter Estimation of the Fricke-Morse Model”, Advances in Electrical and Computer Engineering (IF: 0.459), vol. 16, no. 4, pp. 57-62, 2016, ISSN: 1582-7445, doi: 10.4316/AECE.2016.04009

A. Pajkanović, G. Stojanović, S. Đurić, “Performance Analysis of Meander-Type Inductor in Silicon and Flexible Technology”, Microelectronics Journal (IF: 0.876), vol. 56, pp. 57-64, 2016, ISSN: 0026-2692, doi: https://doi.org/10.1016/j.mejo.2016.07.016

S. Savić, G. Stojanović, D. Vasiljević, K. Vojisavljevic, A. Dapčević, A. Radojković, S. Pršić, G. Branković, “Nanoindentation study of nickel manganite ceramics obtained by a complex polymerization method”,   Ceramics International (IF: 2.986), vol. 42, no. 10, pp. 12276-12282, 2016, ISSN: 0272-8842, doi: http://dx.doi.org/10.1016/j.ceramint.2016.04.174

K. Cvejin, M. Sliwa, L. Manjakkal, J. Kulawik, G. Stojanović, D. Szwagierczak, “Impedancemetric NO sensor based on YSZ/perovskite neodymium cobaltite operating at high temperatures”, Sensors and Actuators B – Chemical (IF: 4.097), vol. 228, pp. 612-624, 2016, ISSN: 0925-4005, doi: http://dx.doi.org/10.1016/j.snb.2016.01.071.

Dj. Tripkovic, J. Vukmirovic, B. Bajac, N. Samardzic, E. Djurdjic, G. Stojanović, V. Srdic, “Inkjet patterning of in situ sol-gel derived barium titanate thin films”, Ceramics International (IF: 2.986), vol. 42, no. 1, pp. 1840-1846, 2016, ISSN: 0272-8842, doi:10.1016/J.CERAMINT.2015.09.148

L. Manjakkal, K. Cvejin, J. Kulawik, K. Zaraska, D. Szwagierczak, G. Stojanović, “Sensing mechanism of RuO2-SnO2 thick film pH sensors studied by potentiometric method and electrochemical impedance spectroscopy”, Journal of Electroanalytical Chemistry (IF: 2.729), vol. 759, pp. 82-90, 2015, ISSN: 1572-6657, http://dx.doi.org/10.1016/j.jelechem.2015.10.036

N. Samardžić, M. Mionić, B. Dakic, H. Hofmann, S. Dautović, G. Stojanović, “Analysis of Quantized Electrical Characteristics of Microscale TiO2 Ink-Jet Printed Memristor”, IEEE Transaction on Electron Devices (IF 2.358), vol. 62, no. 6, pp. 1898-1904, 2015, ISSN: 0018-9383, doi: 10.1109/TED.2015.2421283

N. Lečić, G. Stojanović, S. Đurić, E. Laboure, “Design and Analysis of Planar Symmetric Six-Phase Coupled Inductors“, IEEE Transactions on Magnetics (1.213), vol. 51, no. 6, DOI: 10.1109/TMAG.2014.2383358, 2015, ISSN 0018-9464

B. Milinković, M. Milićević, Đ. Simić, G. Stojanović, R. Đurić, “Low-pass filter for UWB system with the circuit for compensation of process induced on-chip capacitor variation”, Informacije MIDEM – Journal of Microelectronics, electronic components and materials (IF: 0.433), vol. 45, no. 4, pp. 266-276, 2015, ISSN: 0352-9045.

M. Radovanović, B. Mojić-Lante, K. Cvejin, V. Srdić, G. Stojanović, “A Wireless LC Sensor Coated with Ba0.9Bi0.066TiO3 for Measuring Temperature”, Sensors (IF: 2.033), vol. 15, no. 5, pp. 11454-11464, 2015, ISSN: 1424-8220, doi:10.3390/s150511454

J. Vukmirovic, Đ. Tripkovic, B. Bajac, S. Kojic, G. Stojanovic, V. Srdic, “Comparison of barium titanate thin films prepared by inkjet printing and spin coating”, Processing and Application of Ceramics (IF: 0.944), vol. 9, no. 3, pp. 151-156, 2015, ISSN: 1820-6131, doi: 10.2298/PAC1503151V

M. Bošković, M. Perović, M.  Vučinić-Vasić, V. Spasojević, G. Stojanović, B. Antić, “Mossbauer Spectra and Crystallite Size Related Magnetic/Electric Properties of Yb Substituted Zn-Ferrite Nanoparticles”, Nanoscience and Nanotechnology Letters (IF: 1.444), vol. 6, no. 4, pp. 314-318, 2014, ISSN: 1941-4900, doi:10.1166/nnl.2014.1758

S. Đurić, G. Stojanović, “A Compact Planar Transformer With an Improved Winding Configuration,“ IEEE Transactions on Magnetics (IF: 1.386), vol. 50, no. 11, DOI: 10.1109/TMAG.2014.2321630, 2014, ISSN: 0018-9464.

S. Kojić, S. Ajkalo, M. Gužvica, D. Vasilјević, M. Radovanović, G. Stojanović, “A Counter of Number of Products on the Shelf Influences on Capacitance of Interdigitated Capacitor with Application in Intelligent Packaging“, Journal of Microelectronics, Electronic Components and Materials (MIDEM) (IF: 0.242), vol. 44, no. 4, pp. 321-329, 2014, ISSN: 0352-9045

M. Vučinić-Vasić, M. Bošković, A. Antić, G. Stojanović, M. Radovanović, M. Fabian, C. Jovalekić, M. Pavlović, B. Antić, “Temperature induced evolution of structure/microstructure parameters and their correlations with electric/magnetic properties of nanocrystalline Nickel ferrite”, Ceramics International (IF: 2.086), vol. 40, no. 3, pp. 4521 – 4527, 2014, ISSN: 0272 – 8842, doi: https://doi.org/10.1016/j.ceramint.2013.08.127

G. Stojanović, V. Mandić, M. Ćurčić, D. Vasiljević, M. Kisić, N. Radosavljević, “Combining rapid prototyping techniques in mechanical engineering and electronics for realization of a variable capacitor”, Rapid Prototyping Journal (IF: 2.031), vol. 20, no. 2, pp. 115-120, 2014, ISSN: 1355-2546, DOI: 10.1108/RPJ-07-2012-0061

D. Krklješ, D. Vasiljević, G. Stojanović, “A Capacitive Angular Sensor with Flexible Digitated Electrodes”, Sensor Review (IF: 0.740), vol. 34, no. 4, pp. 382-388, 2014, ISSN: 0260-2288, doi: https://doi.org/10.1108/SR-11-2012-683

M. Vučinić-Vasić, E. Božin, L. Bessais, G. Stojanović, U. Kozmidis-Luburić, J. Abeykoon, M. Bostjan, A. Kremenović, B. Antić, “Thermal Evolution of Cation Distribution/Crystallite Size and Their Correlation with the Magnetic State of Yb-Substituted Zinc Ferrite Nanoparticles”, Journal of Physical Chemistry C (IF: 4.835), vol. 117, no. 23, pp. 12358-12365, 2013, ISSN: 1932-7447, doi:10.1021/jp403459t

A. Menićanin, Lj. Živanov, G. Stojanović, N. Samardžić, D. Randjelović, “Transport Parameters of Inkjet Printed Nanoparticle Silver on Polyimide Substrate Measured at Room and Liquid Nitrogen Temperatures“, IEEE Transactions on Electron Devices (IF: 2.358), vol. 60, no. 9, pp. 2963-2967, 2013, ISSN: 0018-9383, doi: 10.1109/TED.2013.2274661

S. Đurić, G. Stojanović, M. Damnjanović, E. Laboure, “Analysis of the Coupling Effect in Different Meander- Type Winding Planar Transformers,“ IEEE Transactions on Magnetics (IF: 1.213), vol. 49, no 7, pp. 3993-3996, 2013, ISSN 0018-9464, doi: 10.1109/TMAG.2013.2243417

N. Jeranče, N. Bednar, G. Stojanović, “An Ink-Jet Printed Eddy Current Position Sensor”, Sensors (IF: 2.048), vol. 13, no. 4, pp. 5205-5219, 2013, ISSN 1424-8220, doi:10.3390/s130405205

N. Bednar, G. Stojanović, “An Organic Electronics Laboratory Course for Graduate Students in Electrical Engineering”, IEEE Transactions on Education (IF: 1.221), vol. 56, no. 3, pp. 280-286, 2013, ISSN: 0018-9359, doi: 10.1109/TE.2012.2216527

N. Bednar, J. Matović, G. Stojanović, “Properties of Surface Dielectric Barrier Discharge Plasma Generator for Fabrication of Nanomaterials”, Journal of Electrostatics (IF:1.265), vol. 71, no 6, pp. 1068-1075, 2013, ISSN 0304-3886, doi: http://dx.doi.org/10.1016/j.elstat.2013.10.010

N. Jeranče, G. Stojanović, N. Samardžić, D. Kesler, “Parallel computing applied to inductance calculation for flexible inductors”, COMPELThe international journal for computation and mathematics in electrical engineering (IF: 0.440), vol. 32, no. 3, pp. 1067-1081, 2013, ISSN: 0332-1649, DOI: 10.1108/03321641311306097

G. Stojanović, G. Kitić, S.M. Savić, V. Crnojević-Bengin, “Electrical Characterization of Nickel Manganite Powders in High-Frequency Range”, Journal of Alloys and Compounds (IF: 2.726), vol. 554, pp. 264-270, 2013, ISSN: 0925-8388, http://dx.doi.org/10.1016/j.jallcom.2012.11.184

K. Cvejin, B. Mojić, N. Samardžić, V. V. Srdić, G. M. Stojanović, “Dielectric studies of barium bismuth titanate as a material for application in temperature sensors”, Journal of Materials Science: Materials in Electronics (IF: 1.966), vol. 24, pp. 1243-1249, 2013, ISSN: 0957-4522, https://doi.org/10.1007/s10854-012-0914-3

N. Samardžić, N. Jeranče, G. Stojanović, “Novel Solution for Flexible Inductive Position Sensor”, Sensor Letters (IF: 0.558), vol. 11, no. 10, pp. 1881-1886, 2013, ISSN: 1546-198X, doi: https://doi.org/10.1166/sl.2013.3046

M. Maksimović, G. Stojanović, M Radovanović, M. Malešev, V. Radonjanin, G. Radosavljević, W. Smetana, “Application of a LTCC sensor for measuring moisture content of building materials”, Construction and Building Materials (IF: 2.293),  vol. 26, no. 1, pp. 327-333, 2012, ISSN: 0950-0618, doi: 10.1016/j.conbuildmat.2011.06.029

N. Jeranče, D. Vasiljević, N. Samardžić, G. Stojanović, “A compact inductive position sensor made by inkjet printing technology on flexible substrate”, Sensors (IF: 1.953), vol. 12, pp. 1288-1298, 2012, ISSN: 1424-8220, doi:10.3390/s120201288

S. Đurić, G. Stojanović, M. Damnjanović, M. Radovanović, E. Laboure, “Design, Modeling, and Analysis of a Compact Planar Transformer”, IEEE Transactions on Magnetics (IF: 1.422), vol. 48, no. 11, pp. 4135-4138, 2012, ISSN: 0018-9464, doi: 10.1109/TMAG.2012.2202642

V. Radonić, K. Palmer, G. Stojanović, V. Crnojević-Bengin, “Flexible Sierpinski Carpet Fractal Antenna on a Hilbert Slot Patterned Ground”, International Journal of Antennas and Propagation (IF: 0.683), vol. 2012, article no. 980916, pp. 1-7, 2012, ISSN 1687-5869, doi: 10.1155/2012/980916

M. Milanović, G. Stojanović, Lj. M. Nikolić, M. Radovanović, B. Škorić, A. Miletić, “Electrical and structural characterisation of nanostructured titania coatings deposited on interdigitated electrode system”, Materials Chemistry and Physics (IF: 2.234), vol. 130, no. 1-2, pp. 769-774, 2011, ISSN: 0254-0584,  doi: 10.1016/j.matchemphys.2011.07.061

S. Savić, L. Mančić, K. Vojisavljević, G. Stojanović, Z. Branković, O. Aleksić, G. Branković, “Microstructural and electrical changes in nickel manganite powder induced by mechanical activation”, Materials Research Bulletin (IF: 2.105), vol. 46, no. 7, pp. 1065-1071, 2011, ISSN: 0025-5408, doi: 10.1016/j.materresbull.2011.03.008

G. Stojanović, N. Lečić, M. Damnjanović, Lj. Živanov, “Electrical and temperature characterization of NiZn ferrites”, International Journal of Applied Electromagnetics and Mechanics (IF: 0.122), vol. 35, no 3, pp. 165-176, 2011, ISSN 1383-5416, doi: 10.3233/JAE20111329

G. Stojanović, M. Radovanović, M. Malešev, V. Radonjanin, “Monitoring of Water Content in Building Materials Using a Wireless Passive Sensor”, Sensors (IF: 1.821), vol. 10, no. 5, pp. 4270-4280, 2010, ISSN: 1424-8220, https://doi.org/10.3390/s100504270

M. Damnjanović, Lj. Živanov, G. Stojanović, A. Menićanin, “Influence of Conductive Layer Geometry on Maximal Impedance Frequency Shift of Zig-Zag Ferrite EMI Suppressor”, IEEE Transactions on Magnetics (IF: 1.061), vol. 46, no. 6, pp. 1303-1306, 2010, ISSN: 0018-9464, doi: 10.1109/TMAG.2010.2042571

A. Zoranović, G. Stojanović, V. Malbaša, “Development of an MP3 player using an MP3 hardware decoder”, International Journal of Electrical Engineering Education (IF: 0.158), vol. 47, no. 3, pp. 329-342, 2010, ISSN: 0020-7209

S. Savić, G. Stojanović, M. Vesna Nikolić, O. Aleksić, D. Luković-Golić, P. Nikolić, “Electrical and transport properties of nickel manganite obtained by Hall effect measurements”, Journal of Materials Science: Materials in Electronics (IF: 1.020), 2009, vol. 20, no. 3, pp. 242-247, ISSN: 0957-4522, doi: 10.1007/s10854-008-9710-5

G. Stojanović, S. Savić, Lj. Živanov, “Important Role of the Hall Effect Measurement System in a Modified Course of Materials in Electrical Engineering”, IEEE Transaction on Education (IF: 0.822), 2009, vol. 52, no. 3, pp. 297-304, ISSN: 0018-9359, doi: 10.1109/TE.2008.928206

M. Satarić, N. Bednar, B. Satarić, G. Stojanović, “Actin Filaments as Nonlinear RLC Transmission Lines”, International Journal of Modern Physics B (IF: 0.408), 2009, vol. 23, no. 22, pp. 4697-4711, ISSN: 0217-9792, https://doi.org/10.1142/S021797920905331X

M. Damnjanović, G. Stojanović, Lj. Živanov, “An educational software tool for design of ferrite EMI suppressors”, International Journal of Electrical Engineering Education (IF: 0.106), 2009, vol. 46, no. 3, pp. 225-238, ISSN: 0020-7209

G. Stojanović, V. Srdić, M. Maletin, “Electrical properties of yttrium-doped Zn and Ni–Zn ferrites”, Physica Status Solidi (a): Applications & Materials Science (IF: 1.205), 2008, vol. 205, no. 10, pp. 2464-2468, ISSN: 0031-8965, doi: 10.1002/pssa.200723525

G. Stojanović, M. Damnjanović, Lj. Živanov, “Temperature dependence of electrical parameters of SMD ferrite components for EMI suppression”, Microelectronics Reliability (IF: 1.29), 2008, vol. 48, no. 7, pp. 1027-1032, ISSN: 0026-2714, doi: 10.1016/j.microrel.2008.03.020

M. Damnjanović, G. Stojanović, V. Desnica, Lj. Živanov, R. Raghavendra, P. Bellew, N. Mcloughlin, “Analysis, design and characterization of ferrite EMI suppressors,” IEEE Transactions on Magnetics (IF: 0.938), 2006, vol. 42, no. 2, pp. 270-277, ISSN: 0018-9464, doi: 10.1109/TMAG.2005.860485

G. Stojanović, M. Damnjanović, V. Desnica, Lj. Živanov, R. Raghavendra, P. Bellew, N. Mcloughlin, “High performance zig-zag and meander inductors embedded in ferrite material,” Journal of Magnetism and Magnetic Materials (IF: 1.212), no. 2, 2006, pp. 76-83, ISSN: 0304-8853, doi: 10.1016/j.jmmm.2005.02.058

M. Damnjanović, G. Stojanović, Lj. Živanov, V. Desnica, “Comparison of different structures of ferrite EMI suppressors,“ Microelectronics International (IF: 0.474), vol. 23, no. 3, pp. 42-48, 2006, ISSN: 1356-5362, doi: 10.1108/13565360610680758

G. Stojanović, Lj. Živanov, “Novel efficient method for inductance calculation of inductors with optimized layout,” International Journal of RF and Microwave Computer-Aided Engineering (IF: 0.496), 2006, vol. 16, no. 5, pp. 463-469, ISSN: 1096-4290, doi: 10.1002/mmce.20166

G. Stojanović, Lj. Živanov, M. Damnjanović, “Novel efficient methods for inductance calculation of meander inductor,“ COMPEL – The international journal for computation and mathematics in electrical engineering (IF: 0.274), 2006, vol. 25, no. 4, pp. 916-928, ISSN: 0332-1649, doi:  10.1108/03321640610684079

G. Stojanović, A. Marić, Lj. Živanov, “Review of various realizations of integrated monolithic transformers“, MIDEM – Journal of microelectronics, electronic components and materials, (IF: 0.085), vol. 35, no. 3, pp. 122-132, 2005, ISSN: 0352-9045

R. Raghavendra, P. Bellew, N. Mcloughlin, G. Stojanovic, M. Damnjanovic, V. Desnica, Lj. Zivanov, “Characterization of Novel Varistor+Inductor Integrated Passive Devices,” IEEE Electron Device Letters (IF: 2.538), vol. 25, no. 12, pp. 778-780, 2004, ISSN: 0741-3106, doi: 10.1109/LED.2004.838321